Team Louët @ Louet Support

  • Total activity 557
  • Last activity
  • Member since
  • Following 0 users
  • Followed by 3 users
  • Votes 1
  • Subscriptions 305

Articles

Recent activity by Team Louët @ Louet Support Recent activity Votes

  • Jane - optimal weaving area

    1. Weaving
    2. FAQ

    We are often asked how much you can weave before advancing the warp.The Jane has clamps on the sides to keep the reed back against the castle, so that you increase the depth of the weaving area. Fo...

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 10 votes

  • Jane Loom - Kombo Loom - Knotting the Harness Cord

    1. Weaving
    2. Operating Instructions

    This diagram demonstrates how to create the correct knot when attaching the toggle cords of a Jane loom to their harnesses. Attach the cord to the eye of the side of a shaft. Use the knot shown in ...

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 9 votes

  • Spinning Wheel - Flyer with sliding hooks

    1. Spinning
    2. FAQ

    As of late 2007 Louet started shipping wheel models S10, S10DT, S51 and S51DT with flyers that have sliding hooks: same as the high speed flyer.  INSTRUCTIONS TO TIGHTEN SLIDER HOOKS Remove the sl...

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • -1 votes

  • Jane warp beam winding direction

    1. Weaving
    2. FAQ

    The back beam on my Jane Loom winds in the opposite direction of any loom I have ever woven on before. Is this part of the design? The Jane Loom beam does wind on differently than most table looms....

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 22 votes

  • David-1 - 4 shaft conversion kit s to a 4-shaft

    1. Weaving
    2. Product Information

    In the initial production runs, there was a David loom with 4 shafts and 6 treadles. Since 2002, only the 8-shaft David has been available. This version did not yet include a brake di...

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 1 vote

  • Delta Loom Instructions

    1. Weaving
    2. Assembly Instructions

    Here are the instructions for the Delta loom

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • -1 votes

  • David - Adding or moving heddles

    1. Weaving
    2. Operating Instructions

    Adding and moving heddles on the David loom is not difficult, but you need to keep a few things in mind. Namely, the shafts of the David can become unbalanced if all the heddles are on one side. Wh...

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 15 votes

  • Magic Dobby instruction manual

    1. Weaving
    2. Assembly Instructions

    See instructions below

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 7 votes

  • Jane Loom toggle pivot is broken

    1. Weaving
    2. FAQ

      Louet has a repair kit for this. In the first series of Jane looms, the pivot holes of the toggles were too tight on the toggle hinges and some of them broke. mail to support@louet.zendesk.com   

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 2 votes

  • Magic Dobby Interface instructions

    1. Weaving
    2. Assembly Instructions

    Original instructions for the Magic Electronic Dobby produced in Canada

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 0 votes