Team Louët @ Louet Support

  • Total activity 547
  • Last activity
  • Member since
  • Following 0 users
  • Followed by 3 users
  • Votes 1
  • Subscriptions 305

Articles

Recent activity by Team Louët @ Louet Support Recent activity Votes

  • Spinning wheel - Double Treadle wheel clicks while treadling

    1. Spinning
    2. FAQ

    This applies to all DT wheels Question: I have a double-treadle, and it makes a clicking noise when the right treadle goes down. It's taken me a while to figure out the source of the noise, but I f...

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 3 votes

  • Jane 8 relevant measurements and information

    1. Weaving
    2. Product Information

    Jane 8 shaft information (original 8 shaft only)   Loom Dimensions Jane 40 - 57 x 75 x 65 cm (22 3/8′′ x 29 1/2′′ x 25 5/8′′) Jane 50 - 67 x 75 x 65 cm (25 1/8′′ x 29 1/2′′ x 25 5/8′′) Jan...

    • Team Louët @ Louet Support
    • Updated
    • 2 followers
    • 0 comments
    • 17 votes

  • Victoria - High Speed Set

    1. Spinning
    2. Product information

    Instructions and general information Push the small whorl as far as it will go on the front of the whorl shaft. I recommend using a socket or pipe with the same diameter as the pulley to prevent cr...

    • Team Louët @ Louet Support
    • Updated
    • 2 followers
    • 0 comments
    • -2 votes

  • A shaft is slanted - Megado

    1. Weaving
    2. FAQ

    See this Article - Megado - a shaft is slanted

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 0 votes

  • Victoria - Footman Bolt Assembly

    1. Spinning
    2. Product information

    The footman bolt assembly on the older version (circa 1998) of the Victoria was attached with a screw. Some times, when you ply long enough the screw would eventually start unscrewing and come out....

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 0 votes

  • General - My Loom Squeaks

    1. Weaving
    2. FAQ

    Depending on use and climate a loom can start squeaking. Use Dry Spray teflon lubricant  Megado Megado can start squeaking, usually from the knife bar groove. Spray it in the knife bar groove, on b...

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 13 votes

  • Lisa Loom Instructions

    1. Weaving
    2. Assembly Instructions

    Download the instructions for the Lisa Loom: The instructions for the Lisa Small differ from those for the medium, large, and extra-large.

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 3 votes

  • Victoria - bobbin makes alot of noise

    1. Spinning
    2. FAQ

      With a Louet Scotch tension wheel, Victoria or S10C, if you sit down behind the wheel and start treadling, without fiber and without actually trying to spin, there can be a loud screeching sound ...

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • -1 votes

  • Jane loom reed dimensions

    1. Weaving
    2. Product Information

    The maximum reed width for the Jane 40 loom is 18 1/4″. The maximum reed width for the Jane 50 loom is 24 1/8″. The maximum reed width for the Jane 70 loom is 30″. The height can be up to 5 1/4" fo...

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 12 votes

  • jane Floorstand - Parts List - assembly instructions

    1. Weaving
    2. Product Information

    download the assembly instructions - new version 2024

    • Team Louët @ Louet Support
    • Updated
    • 1 follower
    • 0 comments
    • 7 votes